ZCP3 Password problems
Good day. One of our ZCP3 panels lost its password data. We cannot log in into the setup or the maintenance menu. What could have caused this and how do I fix it? Thanks
View Articlectec xfp
We've got a site with an xfp panel and 2 repeaters. The thing is when a device is activated it displays on main panel and repeaters ok but it won't light up zonal LED on both repeaters? I've tested...
View ArticleMINERVA 80 AND 500/900 DEVICE COMPATIBILITY
Does anyone know for sure about the compatibility of the adt minerva 80 and 500/900 series devices? specifically on a system with 501 & 901 smokes and 520/920 mcps mixed can you: 1 - mix 500 and...
View ArticleZITON PLANNER
I HAVE OLD PLANNER VERSIONS.I AM LOOKING FOR THE NEW VERSION THAT RUNS ON WIN8
View Articlejsb firedex bi wire 2204
To cut a long story short, idiot sparky has replaced a conventional panel with the above, and fitted a new zone with bi wire detectors/sounders (all second hand of course) Rest of the system is really...
View ArticleClik here to view.
can you identify this PCB
Hi Folks - does anyone recognise this Smoke vent PCB, appreciation in advance. Cheers Bill   SV PCB.jpg (Size: 535.86 KB / Downloads: 8)
View Articleminerva 80 isolate fire & fault relays
for ease of maintenance is there a way to software isolate the fire and fault main panel relays on a minerva 80? I don't want to disconnect the wires if not absolutely necessary. i know how to turn off...
View ArticleZone detectors
I seem to remember bs5839 requiring a maxium of 20 detectors per zone , but looking at the standards I cannot find it , any ideas
View ArticleStripping FP - Jokari Cable Stripper.
Thinking of buying a Jokari Cable Stripper for FP, has anyone used one? Are they any good or a waste of money? Any other recommendations?
View Articlenew Install
I have to spec and install a complete installation starting next week, it will keep me out of trouble for weeks! I'm interested to know what the opinions are on single loop panels for small jobs? It's...
View ArticleConventional panel day/night mode??
Just wondering if anyone knows if any? Quoting a job with 3 sets of beams and some linear heat so need a panel that has selectable S/C for zones but the ability to switch the beams off during the day?...
View ArticleXenex panel - second fire in same zone
HI, Quick question - would a Xenex panel that is showing a zone 2 fire but has been silenced and not reset resound if a different call point or detector goes off in the same zone or just in a different...
View ArticleClik here to view.
Pastor heat detectors
Hi Has anyone worked with Pastor heat detectors? I'm looking for the latest information on these heat detectors. They are made in Slovenia. Manufacturer is Pastor and heat detector is model TM-1S....
View ArticleMorley external paging interface
Looking for a bit of help with morley paging interface Nothing being sent to pager, interface is setup in peripherals, just looking to see if anyone can help in how to fully setup device so i can see...
View ArticleJSB Sounder Bases discontinued
Evening guys. Was on the telephone and internet today trying to locate a sounder base that is compatible with the Firedex 2208 Bi-Wire but had no joy - an email to Cooper said they had been...
View ArticleAdvanced mx4100 charger too high fault
Hi, have an mx4100 showing a charger too high fault, would anyone have come across this before, or know which one of the pet's onboard might reduce voltage. Currently 29.9v, batteries are ok Thanks
View ArticleNotifier Pearl
Hi Can anyone help me with programming a scope to a pearl. I've put in the scope with its aerial and stuck the tx plus gnd of the panel to the rx and gnd on the scope. its just the programming of the...
View ArticleClik here to view.
PSU EN54-4/A2 certified
Hi, I need to find power supplies EN54-4/A2 certified, and would like to know if anyone had experience using them, and if you had any problem with the batteries internal resistance ? I know C-TEC, and...
View ArticleMorley Network Faults causing spuradic alarrms
Over the past couple of years we have been having problems on two hospital sites where sounders would go off without any fire signals showing on the panels. First cause was found to be the HI 485 fault...
View Articlehow things work
has anybody got a good guide to explain how circuits actually work ie in more detail than connect this bit to that end. I`ts a long weekend and I`m bored thanks.
View Article