vigilon compact resistance problem on a loop
I have a vigilon compact with a fault saying lp1 0v is 18.29 ohm. Anyone have any hints or tips? According to the manual it should be max 13/14/15 ohms. So far I've just been checking connections in...
View ArticleIssue with Advance Panel
Hi Chaps I am service and install engineer with limited commissioning experiance went to do fault finding on 4 loops Advanced panel with loop powered sounders. Fualt is : Call point number 27 in zone 7...
View Articledf4000 loop sounder
anyone got an installation manual for MAS767S sounders? I just want to know about the dil switches Cheers
View ArticleApollo Xpander
Hi Guys, Just a quick heads up that we are having a training day for Apollo Xpander sometime between Firex and the end of June. No date set in stone yet as we would like to know numbers that would be...
View ArticleProtec 6100
Hi, Will be testing the Protec 6100 panel soon. If anyone needs any information about it, let me know. Cheers!
View ArticleClik here to view.
Apollo conventional zone monitor interface
Hey all, we recently finished the installation of a new addressable system within serviced offices. The client wanted to retain the old call points and if possible the bells. I advised against having...
View ArticleClik here to view.
C-TEC CFP
Ladies / Gents Can the black 4 pin, zone / sounder plug - on, connector blocks be purchased as spares for these panels? As a bank of 4 terminals? If so where from? Been called to a couple of these...
View ArticleDifference between an annunciator & repeater panel
What is exactly the difference between the annunciator and a repeater panel. I have always observed the price is high for a repeater panel, whereas for annunciator it is less. Can someone tell me the...
View ArticleClik here to view.
Zonemaster 102At
I have an installation with a Zonemaster 102At [Chubb] No longer under contract with them. I need to add another panel in a warehouse that has detectors that was connected to that panel .Can anyone...
View ArticleRafiki
Anyone come across this clinker before Called to a job in a snooker hall last night to a twinflex that was in fire. One detector was in fire - took it down , blew it out - put it back - back into fire....
View ArticleZiton ZP3 starting to corrupt?
I've got a couple of ZP3's I weekly test and in the last few weeks there are weird symbols corrupting the display, particularly when going through the menus when they change. Client is aware and thus...
View ArticleSmoke vent windows linked to Gents Vigilon
Hi Chaps I called today to site to check status of smoke vents windows. System consist of: Small motorized wall window with its own power supply unit and Interface box mounted beside in ground floor by...
View ArticleMorley Ias RS232
Does anyone have information of communication protocol Zxse fire stations via RS232 to connect on 3rd systems.Morley Ias Visualeyez not an option, because building have own managment system. Best regards.
View ArticleKidde 3k9 EOLM units by Kentec
I needed 20 of these 3k9 units, made by Kentec, for a site where the panels had been replaced, but the installer had fitted the original resistors, on Kidde Firebeta panels. Kentec would only make me a...
View ArticleFiredex 2208 Bi-Wire
Hi Any one knows where can I get fire panel JSB :Firedex 2208 Bi-Wire
View ArticleClik here to view.
kidde vega keyswitch isolation
Hi all, in need of a little help. It’s been a long time since writing cause and effect on a kidde Vega. Now I’m in front of one and can’t remember if it is possible, or how to set up an xp95 I/O input...
View ArticleProtec 6300
I'm doing some works on a site and wondered if I could relocate devices without a protec engineer. They will be in different places of the loop, but didn't know if this would bugger the addressing up...
View Articlecall points on stairs of hmo
Hi chaps I serviced conventinal system today in block of flats , the building is 5 levels from ground to 4th floor, it has only 1 call point by main exit from ground floor, whats the regs regarding...
View Articlelaggy / slow controls on kentec syncro
hello, has anyone come across problems with the controls on a kentec syncro after upload? on a few of my sites recently I have found after doing some work on the panel, and uploading the config...
View ArticleClik here to view.
hochiki smoke detector
20150624_090113.jpg (Size: 775.61 KB / Downloads: 4) 20150624_090058.jpg (Size: 1.11 MB / Downloads: 2) 20150624_091244.jpg (Size: 679.71 KB / Downloads: 4) Hi chaps one of our sites has morley...
View Article