Syncro panel question
Hi all , I have recently been to a job of ours where a previous engineer has deleted device information accidently on a Syncro panel. I have the software but my question is , " what is the procedure...
View ArticleZettler Profile - Any opinions?
We've been using the Tyco Minerva MX panels for a few years, and have been thinking of getting in some Zettler Profiles to trial. Tried to search for reviews, but haven't found anything. Has anyone...
View Article2 gent vigilon issues
morning. 2 questions about gent vigilons 1 - we have a vigilon network (8 panels linked by 3 fibre optic network nodes and all 3 are set as node 1 on different domains) with an intermittent wiring...
View Articleare apollo xp95 drop front mcps still available?
are apollo xp95 drop front mcps still available? we have a site with old apollo xp95 square mcps and drop front apollo xp95 mcps. we don't want to introduce a third type of the new new Apollo xp95...
View ArticleRafiki problem
Public house with 11 "lodges" in the ground, Plastic 4 Zone Rafiki controls interconnected into an 8 Zone metal Rafiki controls There are 11 circuits each with 1 sounder/ multi sensor & mcp The...
View ArticleAdvanced Cause & Effect
Hopefully someone can help me out. Im rather used to doing cause & effect on gent panels which i find much simplier rather than advanced and as such i've ran into a slight issue. The site has 4...
View Articlerepeater panel and audible buzzers
is it necessary to have an audible buzzer on a repeater panel? we have a panel where the led's light up but no buzzer operates. bs or en54 and does anyone have a manual for a protec s400 repeater panel?
View ArticleDevices Older than Manufacturers Recommendation
How are you coding for detectors older than 10 years? I always code as C3 improvement recommended marking the certificate satisfactory, this is generally ignored by the end users with the devices left...
View ArticleSyncro AS
Is it possible to set up a Kentec Syncro so that if zone one is activated only the sounders in zone one will sound? I guess this can be done by writing a cause and effect but i is there a simpler way?
View Articlemorley device values
is there an appendix to device values for morley panels? e.g. low output = x, means x, device fault = x, means x. mostly Apollo xp95 but other values appreciated. I rang morley tech and they were no...
View Article1amp sounder cct
Just wondering any panels out there with 1amp sounder ccts, looking on kentec,haes etc they only seem to have 500ma
View ArticleAdvance MX4 with XP95
Morning guys. Please could you assit with my query, I have been asked to design a small system to a L2 standard using an Advance MX4 panel with Apollo XP95 protocol detection. This is not a system I am...
View ArticleNotifier Waterproof Addressable Sounders
Hi Has anyone else noticed how the Notifier Waterproof Addressable Sounders are not really waterproof. I've swapped loads of them mostly in chillers
View ArticleEngraved zone plan
Morning all I have a job to quote and it wants the zone plan to a satin aluminium engraved zone plan. Does anbody know where I can get one made. cheers
View ArticleSigam XT Extinguishant Control Panel K11031m2
Hello, Have this panel showing "CCC" on display. Code not in manual. Any ideas what it means? Cheers, J
View ArticleIR Tester for Seimens Cerberus IR detector?
Hi, does anyone know of a IR torch that will test Seimens Cerberus IR detectors? I bought the apollo one that don't work, hired Hochiki's tester and it was the same as the Apollo one! the only torch...
View Articlexp95 heat detector giving 'bad device reply'
I have an addressable system with a dxc1 morley single loop panel with about 100 devices. I have changed this detector twice to eleminate the fault but I still get the same fault showing. What could be...
View ArticleClik here to view.
C-Tec Panel
WP_20161025_08_58_23_Pro.jpg (Size: 1.48 MB / Downloads: 15) Guys Does anybody know what protocol devices these C-Tec panels use. cheers
View Articlevesda airflow
hello, I've not worked on vesda much but I've managed to force my bosses to buy a HLI and now I have a couple of questions. I had a minor low air flow fault for a couple of pipes around...
View ArticleAritech 2000 series protocol compatibility
Hello, Is it possible to use Aritech 2000 series detectors (e.g.: DP2061N) with fire alarm control panel from different manufacturer (i.e. not from Aritech)? I mean, is the 2000 series Aritech protocol...
View Article